The firmware v1.0.0.0.2 fixed in connecting 12th, 13th channel issue, but it still can site survey (12th, 13th) channel. (20070705_1)
ETSI and FCC Mode can site survey 1~14ch. (20070705_1 #1)
The default SSID should be changed from "Engenius" to "EnGenius". (20070712_2 #7)
In CB info.html, the note "...please close this screen...." should be changed to "…please close this window to get best performance.". (20070712_2 #8)
In AP & CB mode, the SuperAG_mode info. should be re-added on the *info.html because PM has decided to re-enable the mode. (20070712_2 #9)
When setting the country code with super user/pass, the message should be changed to "Please set channel information at Wireless web page after device reboot!". (20070712_2 #11)
In CB mode, the "info" on line#283 of info2.html is not defined so that the RSSI cannot be displayed in WPA/WPA2 mode. (20070712_2 #12)
CB send link down trap continuously in 11b mode, when CB don't associate with any AP.
Release Date Aug 22, 2007
Firmware :EOC-3610-1.0.1.01
HW Version :
New Features
SuperG function
RSSI process bar
Features Enhanced
When the power interrupte many times, the device setting will reset to default. (NCB-8610-SQA-PIL-08102007.xls 20070510_01)
ColdStart should be done in the boot process. (20070712_1 #1)
WarmStart should be sent when rebooting the device. (20070712_1 #2)
Two definitions for same type "DisplayString" in AP MIB. (20070712_1 #3)
In CB mib, the type of "PhysAddress" has two imports. (20070712_1 #4)
Two definitions for same type "PhysAddress" in AP MIB. (20070712_1 #5)
In CB mib, the type of "DisplayString" has two imports. (20070712_1 #6)
In AP mode, the mib of wdsAPMACAddress has no value when it is enabled. (20070712_1 #7)
In the AP MIB descrption, the WDS format should be noted as "ABCDEF123456". (20070712_1 #8)
Release Date Aug 17, 2007
Firmware :ECB-3610-1.0.0.04
HW Version :
Changed
Disable UART(RS-232) function.
Release Date July 17, 2007
Firmware :1.0.0.03
HW Version :
Features Enhanced
In the apply?link= web page under CB mode, the Wireless "Bridger" should be changed to Wireless "Bridge".(20070712_2)
The Turbo_mode on the *.info.html should be removed because PM has decided to remove turbo mode in AP mode.(20070712_2)
In CB mode, the Turbo_mode info should be removed PM has decided to remove turbo mode in AP mode.(20070712_2)
The Preferred BSSID has no value in CB mode.(20070712_3)
In adhoc mode, the Preferred BSSID has no value.(20070712_3)
Release Date July 9, 2007
Firmware :1.0.0.02
HW Version :
New Features
follow 3610 firmware 1.0.0.01
Features Enhanced
CB mode FCC card can connect ETSI 11/12 channel.
Changed
Disable FCC3 function
Release Date June 26, 2007
Firmware :1.0.0.01
HW Version :
New Features
follow 8610 firmware 1.9.7.01
Features Enhanced
CB mode title modify to "Wireless LAN Client Bridge".
Changed
Change default 802.11 Mode "Mixed 802.11g and 802.11b"
Change logo to EnGenius version.
Change default SSID from "default" to "Engenius".
Change Default channel " 1"
Modify AP/CB GUI : SSID/11b/11g combine to wireless_setting ,function Ack_timeout_B/Ack_timeout_G follow user select mode, Ad-hoc mode switch page modify. tx-rate always show b/g, when user select 11g only , the TX rate 1,2,5.5 can't setting,the web page will alert (Can not use 802.11b transmit rates when the 802.11 mode is 802.11g only'),when user select 11b only,the TX rate 6,9,12...54 can't setting,the web page will alert (Can not use 802.11g transmit rates when the 802.11 mode is 802.11b only')
remove telnet 11a function.
Modify AP/CB title :AP: wireless lan access point CB: wireless lan Client Bridge on web GUI